Search

Helicopter Crash Rescue Equipment: H1, H2 and H3 Requirements Explained

Geplaatst op 17 November 2026

When a helicopter operates from a helideck (on a ship or offshore platform) or heliport, regulations require a defined set of rescue tools to be available in case of an accident. If an accident does occur, occupants may be unable to leave the helicopter through its normal exits. In such a situation, the rescue crew needs to be prepared to cut, break or force access to the aircraft to reach the occupants and assist them. A Helicopter Crash Equipment Kit provides the tools needed to do so.

But what exactly should a Helicopter Crash Equipment Kit contain? And how do the requirements differ between the H1, H2 and H3 categories? The answers are not always as straightforward as they might seem.

In this article, we look at the equipment typically required for helicopter crash rescue operations, the role of CAP 437, ICAO requirements and SOLAS, the traditional distinction between H1/H2 and H3 equipment, and what operators should consider when selecting a complete crash rescue kit.

What is a Helicopter Crash Equipment Kit?

A Helicopter Crash Equipment Kit, sometimes referred to as a helicopter crash rescue kit or helideck crash box, brings together the tools that a rescue team may need to quickly gain access to a helicopter and assist its occupants following an incident. In offshore environments, rescue equipment should be available close to the operating area, clearly identifiable and ready for immediate use. This is why the requirements go further than simply having individual tools somewhere on the installation.

For offshore helicopter operations, one of the most important industry references is CAP 437 – Standards for Offshore Helicopter Landing Areas, published by the UK Civil Aviation Authority (CAA). ICAO guidance, SOLAS requirements, flag state regulations and local aviation regulations may also apply depending on the location, type of facility and applicable regulatory framework.

What rescue equipment is required under CAP 437?

CAP 437 specifies a range of rescue equipment that should be readily available for helicopter operations. A typical crash rescue equipment inventory includes equipment such as:

  • Adjustable wrench;
  • Large rescue axe (non-wedge or aircraft type);
  • Bolt cutters;
  • Large crowbar;
  • Grab or salving hook;
  • Heavy-duty hacksaw with six spare blades;
  • Fire-resistant blanket;
  • Two-piece ladder;
  • Lifeline (minimum 15 m length; check the applicable specification for rope circumference) with rescue harness;
  • Side-cutting pliers;
  • Set of assorted screwdrivers;
  • Harness knife with sheath or harness cutters;
  • Man-Made Mineral Fibre (MMMF) filter mask;
  • Fire-resistant gloves.

Note: This inventory is provided for general reference. Operators should verify the latest applicable requirements, including equipment quantities, dimensions and specifications, for their facility.

However, selecting the right rescue equipment involves more than simply ticking these items off a checklist. For example, some personal rescue equipment is related to the number of helideck crew members rather than simply requiring one item per crash box. CAP 437 also makes an important point about the dimensions of rescue equipment: the equipment should be appropriate for the types of helicopter expected to use the facility. That distinction matters.

''Compliance is not simply about having the correct names on an inventory list.
The equipment also has to be suitable for the operation in which it may have to be used''.

What is the difference between H1, H2 and H3 crash equipment?

Under the current CAP 437, there is no longer a difference in the minimum crash box equipment requirements between H1/H2 and H3. Instead, CAP 437 specifies one minimum set of rescue equipment (see list above), which must be appropriate for the types of helicopter using the facility.


So why are H1/H2 and H3 crash kits still commonly specified?

The distinction comes from earlier CAP 437 requirements. The rescue equipment for H1/H2 and H3 was largely the same, with one important difference: H3 additionally required a power cutting tool, together with appropriate training for the personnel using it. This distinction is still widely used when helicopter crash equipment is specified and purchased. In practice, you will therefore still encounter H1/H2 kits and H3 configurations that include additional powered cutting equipment.

Although a power cutting tool is no longer a specific H3 requirement under the current CAP 437 minimum crash box inventory, operators may still consider adding one for additional rescue capability. If required, T-ISS Safety Suppliers can arrange a suitable power cutting tool as an additional option to your Helicopter Crash Equipment Kit.

What does ICAO Doc 9261 say about H3 rescue equipment?

While the current CAP 437 no longer distinguishes between H1/H2 and H3 in its minimum crash rescue equipment inventory, ICAO Doc 9261 (Fifth Edition, 2021) still includes a power cutting tool for helicopters exceeding 24 metres in overall length. This corresponds to the H3 category.

The ICAO Doc 9261 – Heliport Manual, published by the International Civil Aviation Organization (ICAO), is another important international reference that provides guidance on the design, operation and safety requirements of heliports and helidecks, including the rescue equipment needed in the event of a helicopter accident. This creates an interesting difference between the two documents. Under the current CAP 437, a power cutting tool is no longer specifically required for H3 operations, whereas ICAO Doc 9261 continues to identify it as part of the rescue equipment for larger helicopters.

However, it is important to understand that ICAO Doc 9261 is a technical guidance document, not a directly enforceable regulation. Whether its recommendations are mandatory depends on the applicable national aviation regulations, operator requirements and project specifications.

What does this mean when selecting a Helicopter Crash Equipment Kit?

A helicopter crash rescue kit based on the current CAP 437 inventory may be suitable for H1, H2 and H3 operations without a power cutting tool, subject to the applicable requirements and suitability of the individual tools. Where ICAO Doc 9261 is followed or additional rescue capabilities are specified, a power cutting tool may still be necessary for H3 operations, together with appropriate personnel training.

For this reason, T-ISS Safety Suppliers can arrange a suitable power cutting tool as an optional addition to the standard Helicopter Crash Equipment Kit, allowing operators to configure their rescue equipment according to the requirements of their facility.

 

What does SOLAS require for helicopter Crash equipment?

For helicopter operations on ships, SOLAS (International Convention for the Safety of Life at Sea) is another important regulatory reference. SOLAS Chapter II-2, Regulation 18 addresses helicopter facilities on board ships, including fire-fighting arrangements and rescue equipment. SOLAS specifies a minimum inventory of rescue tools, including bolt cutters, a heavy-duty hacksaw, a fire-resistant blanket, a ladder and other equipment needed in an emergency. These requirements largely overlap with the rescue equipment listed in CAP 437, although there are some differences in the specified items and their dimensions.

A CAP 437-based crash kit does not, by itself, establish compliance with all SOLAS requirements for helicopter facilities, including any additional fire-fighting equipment. For operators of ships equipped with helidecks, it is therefore important to consider the applicable SOLAS requirements alongside any relevant aviation standards when selecting a Helicopter Crash Equipment Kit.

A well-equipped Helicopter Crash Equipment Kit is more than a set of tools

When selecting a Helicopter Crash Equipment Kit, operators naturally tend to focus on the tools included. While the contents of a Heli Crash kit are important, they are only part of the picture. Storage, accessibility, inspection and maintenance all play an important role in keeping the equipment ready for use. CAP 437 requires rescue equipment to be properly stored and readily accessible. For offshore installations in particular, the storage solution also has to contend with an aggressive environment involving moisture, salt and weather exposure.

A properly configured crash equipment solution should therefore consider at least five areas:

1. Completeness
Are all required tools and pieces of rescue equipment present? Missing one seemingly small item can mean that the Heli Crash kit no longer matches the required inventory.

2. Suitability
Are the tools appropriate for the helicopters using the facility? The fact that a tool technically appears on an equipment list does not automatically make every size or specification suitable for every operation.

3. Storage and accessibility
Can the rescue team access the equipment immediately? Crash rescue equipment should be stored in an appropriate, clearly identifiable and weather-resistant storage solution.

4. Inspection and maintenance
Is there a routine for checking the contents? A complete kit on the day of installation may no longer be complete several years later. The inventory therefore needs to be checked as part of a planned inspection and maintenance routine.

5. Crew readiness
Does the rescue team know how to use the equipment? Emergency equipment is only valuable when it can be deployed correctly under emergency conditions.

A complete Helicopter Crash Equipment Kit by T-ISS

Sourcing crash rescue equipment individually requires careful attention to each tool’s specification. A wrench, bolt cutter or hacksaw may appear to match an inventory list without necessarily being suitable for the intended application. A pre-assembled Helicopter Crash Equipment Kit simplifies sourcing by bringing together commonly specified rescue tools in one convenient solution. Operators remain responsible for verifying that the selected equipment meets the requirements applicable to their facility.

The T-ISS Helicopter Crash Equipment Kit brings together a selection of rescue tools based on the equipment inventory referenced in CAP 437. Depending on the facility, helicopter types and applicable requirements, additional equipment or specific configurations may be necessary.

The equipment of the T-ISS Heli Crash kit is supplied in a weather-resistant GRP storage box, providing a dedicated location for the supplied rescue inventory. High-quality SafeSign safety signs are included with the kit, allowing the crash box to be clearly identified at the facility.

If your kit becomes incomplete after use, there is no need to replace the entire set. If you prefer, T-ISS Safety Suppliers can supply missing tools and components individually, or advise you on replenishment options.

A manual is also supplied with our kit. This provides the crew with a reference for the equipment provided and allows them to familiarize themselves with the contents and relevant information before the equipment is needed.

By combining the correct rescue tools, dedicated storage, identification and documentation in one solution, the Helicopter Crash Equipment Kit by T-ISS makes it easier for operators to keep their rescue equipment complete, identifiable and ready for use.

Helicopter Crash Equipment Kit FAQ


Can the Helicopter Crash Equipment Kit also be used onshore?

The T-ISS Helicopter Crash Equipment Kit is primarily configured with offshore helicopter operations in mind. Its components may also be considered for onshore heliports and helipads, subject to verification of the applicable requirements. The important difference is the applicable regulation. CAP 437 specifically covers offshore helicopter landing areas. Onshore facilities may instead be subject to ICAO standards, national aviation regulations or local requirements, which can specify different rescue and fire-fighting equipment.

The kit may be considered for onshore applications, but its CAP 437-based configuration should not be taken as proof that it meets every requirement applicable to a particular onshore heliport. For onshore applications, T-ISS Safety Suppliers can provide product information and explain available configuration options. Final verification of applicable requirements and equipment suitability remains the responsibility of the operator or other designated responsible party.

What equipment is required in a helicopter crash rescue kit?

Under the current CAP 437, the minimum crash box inventory includes rescue tools such as an adjustable wrench, rescue axe, bolt cutters, crowbar, grab hook, hacksaw with spare blades, fire-resistant blanket, two-piece ladder, lifeline with rescue harness, side-cutting pliers and a screwdriver set.

Certain items must also be available for each helideck crew member, including a harness knife or harness cutter, an MMMF filter mask and fire-resistant gloves.

What is a CAP 437 crash box?

A CAP 437 crash box is a dedicated storage box or cabinet for rescue equipment associated with an offshore helicopter landing area. The contents and specifications must be checked for the particular facility; a product description alone does not establish regulatory compliance. Equipment should be readily accessible and stored in a clearly identified, secure and weather-protected location.

What is the difference between H1, H2 and H3 helicopter crash equipment?

H1, H2 and H3 are helicopter Rescue and Fire Fighting (RFF) categories. Under the current CAP 437, however, there are no longer separate minimum crash box inventories for H1/H2 and H3. Instead, one minimum rescue equipment list applies, with the size and specification of the equipment being appropriate for the helicopters expected to use the facility.

Does CAP 437 require a power cutting tool for H3?

No, under the current minimum crash box inventory it does not require a power cutting tool. Earlier editions of CAP 437 listed a power cutting tool as an additional requirement for H3, which is why it is still commonly associated with H3 crash kits.

The current CAP 437 no longer lists this as a separate H3 requirement. A power cutting tool can still be added where additional rescue capability is desired or where it is required by a specific project, operator or other applicable standard.

Is a Self-Contained Breathing Apparatus (SCBA) required for helicopter rescue operations?

No, a SCBA is not included in the current CAP 437 minimum crash box inventory. However, CAP 437 recommends that rescue and fire-fighting personnel are provided with appropriate respiratory protective equipment (RPE).

For ships subject to SOLAS helicopter facility requirements, additional fire-fighter’s outfits, including breathing apparatus, are required. At T-ISS, we can supply you with SCBA equipment separately or arrange for it to be included as an optional addition to your Helicopter Crash Equipment Kit, depending on the requirements of your facility.

Can an H1/H2 helicopter crash kit be upgraded to H3?

Under the current CAP 437, the crash box inventory is no longer divided into separate H1/H2 and H3 equipment lists. Therefore, simply adding a power cutting tool to an H1/H2 kit should not automatically be described as an “H3 upgrade”. The applicable requirements should instead be checked against the helicopters, facility and regulations involved.


Do flag state regulations affect helicopter crash equipment requirements?

Yes. For helicopter operations on ships, the vessel’s flag state may influence which safety requirements apply. In addition to international standards such as SOLAS, flag states may impose additional national requirements for helicopter rescue equipment.

Operators should therefore verify the applicable flag state requirements, alongside relevant aviation standards, when selecting a Helicopter Crash Equipment Kit.

How should helicopter crash rescue equipment be stored?

CAP 437 requires rescue equipment to be stored in a clearly marked, secure and watertight cabinet or chest. An inventory checklist should be provided inside so that the contents can be checked and missing equipment can be identified.

How often should a helicopter crash box be inspected?

CAP 437 requires the rescue equipment to be included in a planned maintenance routine, with a responsible person appointed to ensure that regular inspections and maintenance are carried out. Operators should therefore include the crash box in their facility’s established inspection and maintenance programme.

Does every helideck crew member need their own rescue equipment?

Certain items are required for each helideck crew member rather than just once per crash box. Under CAP 437, these are a harness knife and sheath or harness cutters, an MMMF filter mask and a pair of fire-resistant gloves.

Can a helicopter crash equipment kit also be used onshore?

The rescue tools commonly used for offshore helicopter operations may also be considered for onshore heliports and helipads. However, CAP 437 specifically addresses offshore helicopter landing areas.

Onshore facilities may be subject to different national, local or ICAO-based requirements. The equipment requirements for the particular facility should therefore be checked before assuming that a CAP 437 configuration meets all applicable onshore requirements.

How do I know if my helicopter crash rescue kit meets CAP 437 requirements?

Start by comparing the contents of the kit with the current CAP 437 rescue equipment inventory. Do not only check whether each item is present; also check the required dimensions, specifications and quantities, including the equipment that must be provided for each helideck crew member.

Storage, identification, accessibility, inspection and maintenance should also be considered when assessing the complete crash equipment arrangement.

 

Important Notice

This article is for general information only, not regulatory or technical compliance advice. Requirements may vary or change. Purchasers and operators are responsible for checking the suitability of equipment against applicable standards and site-specific needs. T-ISS Safety Suppliers accepts no liability for decisions based solely on this article, to the extent permitted by applicable law.

More related news

Want to know more about our products?
Please contact us.